| Age | Commit message (Collapse) | Author |
|---|
|
commit cf561bad accidentally deleted a line of code that sets the
base_qindex for each frame, which leads to every frame is encoded
at Q of 0.
Change-Id: Ib5f8022e856bf3b3bd0d4147405e46241e3dcf2d
|
|
A problem can arise on static clips with force key frames where
attempts to avoid popping lead to a progressive reduction in key
frame Q that ultimately may lead to unexpected overspend against
the rate target.
The changes in this patch help to insure that in such clips the
quality of the key frames across the clip is more uniform (rather
than starting bad and getting better - especially at low target rates).
This patch also includes a fix that removes a delta on the Y2DC
when the baseline q index < 4 as this is no longer needed.
There is also a fix to try and prevent repeat single step Q adjustment in
the recode loop leading to lots of recodes, especially where the use
of forced skips as part of segmentation has made the impact of Q on
the number of bits generated much smaller.
Patch 2: Amend "last_boosted_qindex" calculation for arf overlay frames.
Change-Id: Ia1feeb79ed8ed014e4239994fcf5e58e68fd9459
|
|
|
|
The commit fixed a problem by capping cpi->active_best_quality to be
smaller than cpi->worst_quality. Also fixed a few line of code that
was misplaced.
Change-Id: Ie908264b72140c669122a0afde5d886619c33474
|
|
This commit removed the macro CONFIG_I8X8, which was used to indicate
the 8x8 intra prediction experiment, made the change fully merged in.
Change-Id: Iafa4443781ce6e83f5591c12ba615a0e92ce0ea0
|
|
This commit enabled the usage of 8x8 intra prediction modes on inter
frames. There are a few TODO items related to this: 1)baseline entropy
need be calibrated; 2)cost of UV need to be done more properly rather
than using decision only relying on Y; 3)Threshold for allowing picking
8x8 intra prediction should be lowered to lower than the B_PRED.
Even with all the TODOs, tests showed consistent gain on derf set ~0.1%
(PSNR:0.08% and SSIM:0.14%). It is assumed that 8x8 intra prediction
will help more on large resolution clips, especially with above TODOs
addressed.
Change-Id: I398ada49dfc32575cfab962a569c2885111ae3ba
|
|
Fixed some further QIndex related issues and replaced some tables
(eg zbin and rounding)
Also Added function (currently disabled by default) to populate the
main AC and DC quantizer tables. Using the original AC range the
resulting computed DC values give behavior broadly comparable
on the DERF set. That is not to say that the equations will hold good
over a more extended range. The purpose of this code is to make it
easier to experiment with further alterations to the Q range and distribution
of Q values plus the relative weights given to AC and DC.
The function find_fp_qindex() ensures that changes to the Q tables
are reflected in the value passed in to the first pass code.
Slight experimental adjustment to static segment Q offset.
Change-Id: I36186267d55dfc2a3d565d0cff7218ef300d1cd5
|
|
This commit added scaling factors to 8x8 transform, quant, dequant and
inverse transform pipeline to make 8x8 transform to work when configed
with enable-extend_qrange. This commit also disabled the trellis-quant
when extend_qrange is configured.
Change-Id: Icfb3192e4746f70a4bb35ad18b7b47705b657e52
|
|
No change to functionality or output.
Updates to the segment feature data structure now all done
through functions such as set_segdata() and get_segdata()
in seg_common.c.
The reason for this is to make changing the structures (if needed)
and debug easier.
In addition it provides a single location for subsequent addition
of range and validity checks. For example valid combination of
mode and reference frame.
Change-Id: I2e866505562db4e4cb6f17a472b25b4465f01add
|
|
Removal of configure #ifdefs so that segment features
always available. Removal of code supporting old
segment feature method.
Still a good deal of tidying up to do.
Change-Id: I397855f086f8c09ab1fae0a5f65d9e06d2e3e39f
|
|
This quite large check in includes the following:
Merge in some code from Ronald (mbgraph.c) that scans a Gf/arf group.
This is used as a basis for a simple segmentation for the normal frames
in a gf/arf group. This code also uses satd functions from Yaowu.
Adds functionality for coding the latest possible position of an EOB for
blocks in the segment. (Currently 0-15 only, hence just for 4x4 dct).
Where the EOB position is 0 this acts like "skip" and the normal coding
of skip at the per mb level is disabled.
Added functions (seg_common.c) for setting and reading segment feature
elements. These may want to be optimized away at some point but while the
mecahnism is in a state of flux they provide a single location for making
changes and keep things a bit cleaner.
This is still proof of concept code. Currently the tested feature set:-
Quantizer,
Loop Filter level,
Reference frame,
Prediction Mode,
EOB end stop.
TBD:-
Add functions for setting and reading the feature data with range
and validity checking.
Handling of signed and unsigned feature data. At the moment all is assumed
to be signed and a sign bit is coded but many cannot be negative.
Correct handling of EOB feature with intra coded blocks.
Testing/trapping of legal/illegal ref frame and mode combinations.
Transform size switch plus merge and test with 8c8 DCT work
Merge and test with Sumans Segmenation coding optimizations
Change-Id: Iee12e83661c7abbd1e0ce6810915eb4ec35e2d8e
|
|
Plumbing for tuning new segment features on and off.
Change-Id: If86cd6f103296b73030e8af7cf85c5b9bbffdbaf
|
|
This data structure is now [Segment ID][Features]
rather than [Features][Segment_ID]
I propose as a separate modification to make the experimental
bit stream reflect this such that all the features for a segment
are coded together.
Change-Id: I581e4e3ca2033bdbdef3d9300977a8202f55b4fb
|
|
Some basic plumbing added for a range of segment level features.
MB_LVL_* changed to SEG_LVL_* to better reflect meaning.
Change-Id: Iac96da36990aa0e40afc0d86e990df337fd0c50b
|
|
With this fix, the experimental branch now builds and encodes correctly
with the following two configure options respectively:
--enable-experimental --enable-t8x8
--enable-experimental
Change-Id: I3147c33c503fe713a85fd371e4f1a974805778bf
|
|
Please refer to previous commit messages for detailed info:
https://on2-git.corp.google.com/g/#change,5940
https://on2-git.corp.google.com/g/#change,6045
Change-Id: I8b16992f2f69c5a808ad40a3e32ef589cce7c59d
|
|
vp8_fast_quantize_b_pair_neon function added to quantize
two adjacent blocks at the same time to improve performance.
- Additional 3-6% speedup compared to neon optimized fast
quantizer (Tanya VGA@30fps, 1Mbps stream, cpu-used=-5..-16)
Change-Id: I3fcbf141e5d05e9118c38ca37310458afbabaa4e
|
|
Group related functions together.
Change-Id: I92fd779225b75a7204650f1decb713142c655d71
|
|
in encodframe.c, quant_shift is set to 0 or 1 in vp8cx_invert_quant
only use 8 bits to store this, instead of 16. will allow saving an
xmm register in an updated version of the regular quantize
Change-Id: Ie88c47fe2aff5af0283dab1147fb2791e4b12f90
|
|
Change-Id: I64fa47889c54cfed094a674c49ef0996d49bdd42
|
|
Allow compiling without adding vp8/{common,encoder,decoder} to the
include paths.
Change-Id: Ifeb5dac351cdfadcd659736f5158b315a0030b6c
|
|
about ~5% gain on 32bit. disabled for 64bit
unset executable bit on ssse3 version (cosmetic)
Change-Id: I1a5860839eb294ce4261f819caea2dcfa78e57ca
|
|
Removing unused local variables causing compiler warnings in
Visual Studio.
Change-Id: I0e2096303be1fdbc01428a6e57cca9796bb32c8a
|
|
Use the fast quantizer for inter mode selection and the
regular quantizer for the rest of the encode for good quality,
speed 1. Both performance and quality were improved. The
quality gains will make up for the quality loss mentioned in
I9dc089007ca08129fb6c11fe7692777ebb8647b0.
Change-Id: Ia90bc9cf326a7c65d60d31fa32f6465ab6984d21
|
|
The fast quantizer assembly code has not been updated to match the new
exact quantizer, which was made the default in commit 6adbe09.
Specifically, they are not aware of the potential for the coefficient
to be scaled, which results in the quantized result exceeding the range
of the DCT. This patch restores the previous behavior of using the
non-shifted coefficients when in the fast quantizer code path, but
unfortunately requires rebuilding the tables when switching between the
two.
Change-Id: I0a33f5b3850335011a06906f49fafed54dda9546
|
|
Small changes to the default zero bin and rounding tables.
Though the tables are currently the same for the Y1 and Y2 cases
I have left them as separate tables in case we want to tune this later.
There is now some adjustment of the zbin based on the prediction mode.
Previously this was restricted to an adjustment for gf/arf 0,0 MV.
The exact quantizer now marginal outperforms and is the default.
The overall average gain is about 0.5%
Change-Id: I5e4353f3d5326dde4e86823684b236a1e9ea7f47
|
|
Most of the code that actually uses these matrices indexes them as
if they were a single contiguous array, and coverity produces
reports about the resulting accesses that overflow the static
bounds of the first row.
This is perfectly legal in C, but converting them to actual [16]
arrays should eliminate the report, and removes a good deal of
extraneous indexing and address operators from the code.
Change-Id: Ibda479e2232b3e51f9edf3b355b8640520fdbf23
|
|
This patch moves the scattered updates to the mb skip state
(mode_info_context->mbmi.mb_skip_coeff) to vp8_tokenize_mb. Recent
changes to the quantizer exposed a bug where if a macroblock
could be coded as a skip but isn't, the encoder would run the
loopfilter but the decoder wouldn't, causing a reference buffer
mismatch.
The loopfilter is controlled by a flag called dc_diff. The decoder
looks at the number of decoded coefficients when setting this flag.
The encoder sets this flag based on the skip state, since any
skippable macroblock should be transmitted as a skip. The coefficient
optimization pass (vp8_optimize_b()) could change the coefficients
such that a block that was not a skip becomes one. The encoder was
not updating the skip state in this situation for intra coded blocks.
The underlying issue predates it, but this bug was recently triggered
by enabling trellis quantization on the Y2 block in commit dcd29e3,
and by changing the quantizer range control in commit 305be4e.
Change-Id: I5cce5da0dbc2d22f7d79ee48149f01e868a64802
|
|
There is currently no inexact version of this function, so do not
even compile it without EXACT_QUANT.
This will prevent someone from inadvertently trying to use it without
the proper EXACT_QUANT setup.
Change-Id: Ia13491e0128afb281c05c9222ee5987101e4010d
|
|
As the zbin and rounding constants are normalized, rounding effectively
does the zbinning, therefore the zbin operation can be removed. In
addition, the memset on the two arrays are no longer necessary.
Change-Id: If39c353c42d7e052296cb65322e5218810b5cc4c
|
|
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
|
|
Change-Id: I8b9fdf9875a8fcff4cb49a3357ce44f18108c2e7
|
|
These copies occurred for each macroblock in the encoder and decoder.
Thetemp MB_MODE_INFO mbmi was removed from MACROBLOCKD. As a result,
a large number compile errors had to be fixed.
Change-Id: I4cf0ffae3ce244f6db04a4c217d52dd256382cf3
|
|
Replace the exponential search for optimal rounding during
quantization with a linear Viterbi trellis and enable it
by default when using --best.
Right now this operates on top of the output of the adaptive
zero-bin quantizer in vp8_regular_quantize_b() and gives a small
gain.
It can be tested as a replacement for that quantizer by
enabling the call to vp8_strict_quantize_b(), which uses
normal rounding and no zero bin offset.
Ultimately, the quantizer will have to become a function of lambda
in order to take advantage of activity masking, since there is
limited ability to change the quantization factor itself.
However, currently vp8_strict_quantize_b() plus the trellis
quantizer (which is lambda-dependent) loses to
vp8_regular_quantize_b() alone (which is not) on my test clip.
Patch Set 3:
Fix an issue related to the cost evaluation of successor
states when a coefficient is reduced to zero. With this
issue fixed, now the trellis search almost exactly matches
the exponential search.
Patch Set 2:
Overall, the goal of this patch set is to make "trellis"
search to produce encodings that match the exponential
search version. There are three main differences between
Patch Set 2 and 1:
a. Patch set 1 did not properly account for the scale of
2nd order error, so patch set 2 disable it all together
for 2nd blocks.
b. Patch set 1 was not consistent on when to enable the
the quantization optimization. Patch set 2 restore the
condition to be consistent.
c. Patch set 1 checks quantized level L-1, and L for any
input coefficient was quantized to L. Patch set 2 limits
the candidate coefficient to those that were rounded up
to L. It is worth noting here that a strategy to check
L and L+1 for coefficients that were truncated down to L
might work.
(a and b get trellis quant to basically match the exponential
search on all mid/low rate encodings on cif set, without
a, b, trellis quant can hurt the psnr by 0.2 to .3db at
200kbps for some cif clips)
(c gets trellis quant to match the exponential search
to match at Q0 encoding, without c, trellis quant can be
1.5 to 2db lower for encodings with fixed Q at 0 on most
derf cif clips)
Change-Id: Ib1a043b665d75fbf00cb0257b7c18e90eebab95e
|
|
To facilitate more testing related to quantizer and rate
control, the old version quantizer is added back. old and
new quantizer can be switched back and forth by define or
un-define the macro "EXACT_QUANT".
Change-Id: Ia77e687622421550f10e9d65a9884128a79a65ff
|
|
This replaces the approximate division-by-multiplication in the
quantizer with an exact one that costs just one add and one
shift extra.
The asm versions have not been updated in this patch, and thus
have been disabled, since the new method requires different
multipliers which are not compatible with the old method.
Change-Id: I53ac887af0f969d906e464c88b1f4be69c6b1206
|
|
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
|
|
Change-Id: I7ccc580410bea096a70dce0cc3d455348d4287c5
|
|
Change-Id: I944035e720ef834561a9da0d723879a4f787312c
|
|
Change-Id: Ieebea089095d9073b3a94932791099f614ce120c
|
|
|
