| Age | Commit message (Collapse) | Author |
|---|
|
And __pthread_rwlock_trywrlock as a compatibility symbol.
Remove the unused __libc_rwlock_trywrlock macro.
The symbols were moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
And __pthread_rwlock_tryrdlock as a compatibility symbol.
Remove the unused __libc_rwlock_tryrdlock macro.
The symbols were moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
And __pthread_rwlock_init as a compatibility symbol.
__libc_rwlock_init is changed to call __pthread_rwlock_init directly.
The symbols were moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
And __pthread_rwlock_destroy as a compatibility symbol.
rwlocks do not need finalization, so change __libc_rwlock_fini to do
nothing.
The symbols were moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
__pthread_setspecific@@GLIBC_2.34 is no longer needed after the move,
so it is removed with this commit, too.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
__pthread_getspecific@@GLIBC_2.34 is no longer needed after the move,
so it is removed with this commit, too.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
__pthread_key_delete@@GLIBC_PRIVATE is no longer needed after that,
so it is removed as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
__pthread_key_create@@GLIBC_2.34 is no longer needed by glibc
itself with this change, but __pthread_key_create is used by
libstdc++, so it still has to be exported as a public symbol.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_exit@@GLIBC_PRIVATE symbol is no longer needed
after this change, so remove it.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
__pthread_mutex_unlock@GLIBC_2.34 is not removed in this commit
because it is still used from nptl/nptl-init.c.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_mutex_trylock@@GLIBC_2.34 symbol version is no longer
needed because the call is now internal to libc, so remove it with
this commit.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_mutex_timedlock@@GLIBC_PRIVATE export is no longer
needed, so it is removed with this commit.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
__pthread_mutex_lock@GLIBC_2.34 is not removed in this commit
because it is still used from nptl/nptl-init.c.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The calls to __pthread_mutex_init, __pthread_mutexattr_init,
__pthread_mutexattr_settype are now private and no longer need
to be exported. This allows the removal of the newly added
GLIBC_2.34 symbol versions for those functions.
Also clean up some weak declarations in <libc-lockP.h> for
these functions. They are not needed and potentially incorrect
for static linking of mtx_init.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_mutex_destroy@@GLIBC_2.34 symbol is no longer
neded because this commit makes __pthread_mutex_destroy@GLIBC_2.0
a compatibility symbol, so remove the new symbol version.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_cond_wait@@GLIBC_PRIVATE symbol is no longer
neded, so remove that as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_cond_timedwait@@GLIBC_PRIVATE symbol is no longer
neded, so remove that as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_cond_signal@@GLIBC_PRIVATE symbol is no longer
neded, so remove that as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_cond_init@@GLIBC_PRIVATE symbol is no longer
neded, so remove that as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_cond_destroy@@GLIBC_PRIVATE symbol is no longer
neded, so remove that as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
The __pthread_cond_broadcast@@GLIBC_PRIVATE symbol is no longer
neded, so remove that as well.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
This change also turns __pthread_once into a compatibility symbol
because after the call_once move, an internal call to __pthread_once
can be used. This an adjustment to __libc_once: Outside libc (e.g.,
in nscd), it has to call pthread_once. With __pthread_once as a
compatibility symbol, it is no longer to add a new GLIBC_2.34
version after the move from libpthread, and this commit removes
the new __pthread_once@@GLIBC_2.34 version.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
These make variables can be used to add routines to different
libraries for the Hurd and Linux builds.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
|
|
This implementation is based on __memset_power8 and integrates a lot
of suggestions from Anton Blanchard.
The biggest difference is that it makes extensive use of stxvl to
alignment and tail code to avoid branches and small stores. It has
three main execution paths:
a) "Short lengths" for lengths up to 64 bytes, avoiding as many
branches as possible.
b) "General case" for larger lengths, it has an alignment section
using stxvl to avoid branches, a 128 bytes loop and then a tail
code, again using stxvl with few branches.
c) "Zeroing cache blocks" for lengths from 256 bytes upwards and set
value being zero. It is mostly the __memset_power8 code but the
alignment phase was simplified because, at this point, address is
already 16-bytes aligned and also changed to use vector stores.
The tail code was also simplified to reuse the general case tail.
All unaligned stores use stxvl instructions that do not generate
alignment interrupts on POWER10, making it safe to use on
caching-inhibited memory.
On average, this implementation provides something around 30%
improvement when compared to __memset_power8.
Reviewed-by: Matheus Castanho <msc@linux.ibm.com>
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
|
|
This implementation is based on __memcpy_power8_cached and integrates
suggestions from Anton Blanchard.
It benefits from loads and stores with length for short lengths and for
tail code, simplifying the code.
All unaligned memory accesses use instructions that do not generate
alignment interrupts on POWER10, making it safe to use on
caching-inhibited memory.
The main loop has also been modified in order to increase instruction
throughput by reducing the dependency on updates from previous iterations.
On average, this implementation provides around 30% improvement when
compared to __memcpy_power7 and 10% improvement in comparison to
__memcpy_power8_cached.
|
|
This patch was initially based on the __memmove_power7 with some ideas
from strncpy implementation for Power 9.
Improvements from __memmove_power7:
1. Use lxvl/stxvl for alignment code.
The code for Power 7 uses branches when the input is not naturally
aligned to the width of a vector. The new implementation uses
lxvl/stxvl instead which reduces pressure on GPRs. It also allows
the removal of branch instructions, implicitly removing branch stalls
and mispredictions.
2. Use of lxv/stxv and lxvl/stxvl pair is safe to use on Cache Inhibited
memory.
On Power 10 vector load and stores are safe to use on CI memory for
addresses unaligned to 16B. This code takes advantage of this to
do unaligned loads.
The unaligned loads don't have a significant performance impact by
themselves. However doing so decreases register pressure on GPRs
and interdependence stalls on load/store pairs. This also improved
readability as there are now less code paths for different alignments.
Finally this reduces the overall code size.
3. Improved performance.
This version runs on average about 30% better than memmove_power7
for lengths larger than 8KB. For input lengths shorter than 8KB
the improvement is smaller, it has on average about 17% better
performance.
This version has a degradation of about 50% for input lengths
in the 0 to 31 bytes range when dest is unaligned.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
|
|
This patch updates the kernel version in the test tst-mman-consts.py
to 5.12. (There are no new MAP_* constants covered by this test in
5.12 that need any other header changes.)
Tested with build-many-glibcs.py.
|
|
Linux 5.12 has one new syscall, mount_setattr. Update
syscall-names.list and regenerate the arch-syscall.h headers with
build-many-glibcs.py update-syscalls.
Tested with build-many-glibcs.py.
|
|
On x86_64, when configuring glibc with CFLAGS="-O2 -g -march=native",
some tests fail. After this patch, "make check" succeeds.
Tested on Intel Core i5-4590 with gcc 10.2.1.
|
|
|
|
GCC 11 warns when a pointer to an uninitialized object is passed
to a function that takes a const-qualified argument. This is done
on the assumption that most such functions read from the object.
For the rare case of a function that doesn't, GCC 11 extends
attribute access to add a new mode called none.
POSIX pthread_setspecific() is one such rare function that takes
a const void* argument but that doesn't read from the object it
points to. To suppress the -Wmaybe-uninitialized issued by GCC
11 when the address of an uninitialized object is passed to it
(e.g., the result of malloc()), this change #defines
__attr_access_none in cdefs.h and uses the macro on the function
in sysdeps/htl/pthread.h and sysdeps/nptl/pthread.h.
|
|
This patch makes build-many-glibcs.py use Linux 5.12 and GCC 11
branch.
Tested with build-many-glibcs.py (host-libraries, compilers and glibcs
builds).
|
|
Checked on ppc64le built without --with-cpu, with --with-cpu=power9
and with --disable-multi-arch.
Reviewed-by: Matheus Castanho <msc@linux.ibm.com>
|
|
During ellipsis processing the collation cursor was not correctly
moved to the end of the ellipsis after processing.
The code inserted the new entry after the cursor, but before the
real end of the ellipsis:
[cursor]
... element_t <-> element_t <-> element_t <-> element_t
"<U0000>" "<U0001>" "<U007F>"
startp endp
At the end of the function we have:
[cursor]
... element_t <-> element_t <-> element_t
"<U007E>" "<U007F>"
endp
The cursor should be pointing at endp, the last element in the
doubly-linked list, otherwise when execution returns to the
caller we will start inserting the next line after <U007E>.
Subsequent operations end up unlinking the ellipsis end entry or
just leaving it in the list dangling from the end. This kind of
dangling is immediately visible in C.UTF-8 with the following
sorting from strcoll:
<U0010FFFF>
<U0000FFFF>
<U000007FF>
<U0000007F>
With the cursor correctly adjusted the end entry is correctly given
the right location and thus the right weight.
Retested and no regressions on x86_64 and i686.
Co-authored-by: Carlos O'Donell <carlos@redhat.com>
|
|
No bug. This commit optimizes strchr-evex.S. The optimizations are
mostly small things such as save an ALU in the alignment process,
saving a few instructions in the loop return. The one significant
change is saving 2 instructions in the 4x loop. test-strchr,
test-strchrnul, test-wcschr, and test-wcschrnul are all passing.
Signed-off-by: Noah Goldstein <goldstein.w.n@gmail.com>
|
|
No bug. This commit optimizes strchr-avx2.S. The optimizations are all
small things such as save an ALU in the alignment process, saving a
few instructions in the loop return, saving some bytes in the main
loop, and increasing the ILP in the return cases. test-strchr,
test-strchrnul, test-wcschr, and test-wcschrnul are all passing.
Signed-off-by: Noah Goldstein <goldstein.w.n@gmail.com>
|
|
The existing definition in libc will be used instead.
The symbol was moved (that is, removed) using
scripts/move-symbol-to-libc.py.
|
|
The existing definition in libc will be used instead.
The symbol was moved (that is, removed) using
scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
|
For some architectures, the two functions are aliased, so these
symbols need to be moved at the same time.
The symbols were moved using scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
|
The symbol was moved using scripts/move-symbol-to-libc.py.
|
